Twice as much coverage through high oil content - saves time and money!
Decorative, satin-matt oil based protective finish for exterior wood furniture. Microporous, breathable finish allowing the wood to breath and reduces the risk of swelling and shrinkage. Water-repellent, extremely weather- and UV-resistant. Contains active ingredients to protect the finish against algae and mildew. The finish is proven over decades in all kinds of climatic conditions, and does not crack, flake, peel or blister. Easy to renew, no sanding or primer necessary. Easy to apply, does not dry during application.
All exterior wood furniture.






Ingredients
Based on natural plant oils, iron oxide and organic pigments, titanium dioxide white pigments, siccatives (drying agents) and additives. Biocidal active ingredient: 3-iodo-2-propynyl butylcarbamate (IPBC). Dearomatised white spirit (benzene-free).
Storage
5 years and longer if stored in the originally closed can. If thickened by frost, store at room temperature for 24 hours prior to use.
COLOUR CODE | CAN SIZE LITRE | ARTICLE NUMBER | |
---|---|---|---|
| 0.75 | 12100001 | |
2.50 | 12100002 | ||
| 0.75 | 12100075 | |
2.50 | 12100085 | ||
| 0.75 | 12100055 | |
2.50 | 12100056 | ||
| 0.75 | 12100004 | |
2.50 | 12100005 | ||
| 0.75 | 12100007 | |
2.50 | 12100008 | ||
| 0.75 | 12100010 | |
2.50 | 12100011 | ||
| 0.75 | 12100013 | |
2.50 | 12100014 | ||
| 0.75 | 12100097 | |
2.50 | 12100096 | ||
| 0.75 | 12100017 | |
2.50 | 12100018 | ||
| 0.75 | 12100035 | |
2.50 | 12100036 | ||
| 0.75 | 12100038 | |
2.50 | 12100039 | ||
| 0.75 | 12100254 | |
2.50 | 12100256 | ||
| 0.75 | 12100264 | |
2.50 | 12100266 | ||
| 0.75 | 12200095 | |
2.50 | 12200097 | ||
| 0.75 | 12100023 | |
2.50 | 12100024 | ||
| 0.75 | 12100026 | |
2.50 | 12100027 | ||
| 0.75 | 12100150 | |
2.50 | 12100151 | ||
| 0.75 | 12100274 | |
2.50 | 12100276 | ||
| 0.75 | 12100284 | |
2.50 | 12100286 |
NUMBER OF COATS
Two coats on raw wood; for renovations, normally one coat on the clean surface is sufficient – without sanding!




Wood surface must be clean, dry and frost-free (moisture content max. 20 %). Clean or slightly sand old microporous finishes, remove old varnish
(Osmo Paint Remover or by sanding). Always wear a dust mask when sanding. Osmo Natural Oil Woodstain is ready-to-use, please do not thin, stir
well before use. If possible, please apply the first coat to all sides before installation. If additional protection against blue stain and rot is desired,
pre-treat, if possible all sides, with Osmo WR Base Coat. Use biocides safely. Always read the label and product information before use.
The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
Apply thinly and evenly along the wood grain with either an Osmo hand brush or the Osmo Microfibre Roller, and spread well. Allow for good ventilation whilst drying. Apply a second coat as before. When renovating one coat, applied to the clean and dry surface, will usually be sufficient.
With Osmo Brush Cleaner (free of aromatic compounds).
Approx. 12 hours (normal climatic conditions, 23 °C/ 50% rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times. After 2-3 weeks, the surface is fully cured.
The transparent colour tone of the finish will be influenced by the woods natural colour, causing the result to deviate from the colour shown on the colour chart. Lightly pigmented transparent finishes offer little protection against UV-influences and are therefore not recommended for surfaces
prone to strong sunlight. The dried surface is lightly satin at first, satin-matt thereafter. To increase the durability of the finish we recommend, after
thorough drying, applying a top coat of Osmo UV-Protection-Oil 410, Clear (not applicable for white stained surfaces, 900). All colour shades can be mixed with each other.
Keep out of reach of children.
Do not get in eyes, on skin, or on clothing.
Contains
3-Iodo-2-propynylbutylcarbamate
May cause an allergic reaction.
If medical advice is needed, have product container or label at hand.
Use only outdoors or in a well-ventilated area.
Harmful to aquatic life with long lasting effects.
Avoid release to the environment.
The dried finish is classified as B2 (normal flammability) according to DIN 4102 regulations.
Safety data sheet available on request.
Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 11*). Only completely emptied cans can be recycled.

HOW MUCH COATING DO I NEED?
With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.