Osmo Farbe

UV-Protection-Oil Extra

colours

Protected prefectly against the sun – transparent, lightly pigmented UV protection for outdoor areas!

Osmo UV-Protection-Oil Extra is a satin, transparent finish for exterior wood furniture. It is based on natural oils, is microporous and does not crack, flake, peel or blister. When used as a final finish after staining wood, Osmo UV-Protection-Oil Extra prolongs the renovation time significantly. A solitary finish, with two coats, it delays the greying process on vertical surfaces by UV-Protection factor 12 in comparison to untreated wood. Easy to renew, no sanding or primer necessary. Easy to apply, will not dry during application.

For all exterior wood furniture in protected areas.

Based on renewable raw materialsMircoporous and breathable surfaceCoating protected against mould, algae and fungal attackFor dimensionally stable / unstable exterior woodRecoatable after approx. 12 hours18 m²/1 lWith film protection
Oil advantages – Simple application, Water beading effect, No flaking or peelingUV-Protected 12x - Tested according to EN 927-6

Ingredients

Based on natural plant oils, iron oxide and organic pigments, titanium dioxide (white pigment), siccatives (drying agents) and additives, biocidal active ingredient: 3-iodo-2-propynyl butylcarbamate (IPBC). Dearomatised white spirit (benzene-free). EU limit value for this pro- duct (cat. A/e): 400 g/l VOC (2010). This product contains max. 400 g/l VOC. Detailed declaration of ingredients available upon request.

Storage

5 years and longer if stored in the originally closed can. If thickened by frost, store at room temperature for 24 hours prior to use.

COLOUR CODECAN SIZE LITREARTICLE NUMBER

420 Clear

Satin

0.7511600026
2.5011600027

424 Spruce

Satin

0.7511600049
2.5011600057

425 Oak

Satin

0.7511600033
2.5011600034

426 Larch

Satin

0.7511600062
2.5011600063

427 Douglas Fir

Satin

0.7511600068
2.5011600069

428 Red Cedar

Satin

0.7511600041
2.5011600042

429 Natural

Satin

0.7511600051
2.5011600052

431 Light Red Cedar

Satin

0.7511600081
2.5011600082

432 Light Oak

Satin

0.7511600092
2.5011600093

NUMBER OF COATS
Two coats on raw wood; for renovations, normally one coat on the clean surface is sufficient – without sanding!

TOOLS
Flat BrushMicrofibre Roller

Wood surface must be clean, dry and frost-free (maximum moisture content 20 %). Osmo UV-Protection-Oil Extra is ready to use, please do no thin, stir well before use. Clean old microporous finishes thoroughly. Remove old varnishes. Please do not sand even surfaces finer than P 120. Always wear a dust mask when sanding. We recommend to apply a first coat with a pigmented oil such as One Coat Only, Natural Oil Wood Stain or Country Colour. If additional protection against blue stain, rot and mildew is required for outdoors pre-treat (if possible from all sides) with Osmo Base Coat WR.

The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.

Apply evenly along the wood grain with either an Osmo Natural Bristle Brush or the Osmo Microfibre Roller, and spread well. Allow for good ventilation whilst drying. Apply a second coat as before. When applying on an already pigmented surface or when renovating 1 coat of the UV-Protection-Oil Extra is enough. Make sure that the surface has been cleaned upfront.

With Osmo Brush Cleaner (free of aromatic compounds).

Approx. 12 hours (normal climatic conditions, 20-23°C/ 50-65 % rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times. After 2-3 weeks, the surface is fully cured.

Tropical hardwoods or oily wood species must be weathered prior to application. Depending on the level of weathering apply 1 coat of Osmo UV-Protection-Oil Extra after approx. 3 - 4 years on the cleaned and intact finish. In general, one has to take a shorter renovation time into account when: 1. surfaces are exposed to extreme weathering, 2. using exotic wood species, 3. surfaces where water cannot drain (horizontal surfaces). The UV-Protection-Oil Extra is unsuitable as a solitary finish on horizontal surfaces. There should be a minimum 15 degree angle on architectural joinery on the horizontal. Sharp edges have to be rounded (corner radius > 2 mm). If the greying process has already begun revive the surface with the Osmo Wood Reviver and re-apply 2 coats of the Osmo UV-Protection- Oil Extra. In order to achieve UV factor 12, it is very important to apply the UVProtection- Oil Extra twice. When only 1 coat has been applied on an untreated wood, the durability will be reduced significantly. UV-Protection-Oil Natural 429 protects wood nearly invisibly. On dark/ reddish wood species, UV-Protection-Oil Natural is visible as slightly white chalky surface. A trial application is recommended.

Keep out of reach of children.

Do not get in eyes, on skin, or on clothing.

Contains

3-Iodo-2-propynylbutylcarbamate

May cause an allergic reaction.

If medical advice is needed, have product container or label at hand.

Use only outdoors or in a well-ventilated area.

Harmful to aquatic life with long lasting effects.

Avoid release to the environment.

 

The dried finish is classified as B2 (normal flammability) according to DIN 4102 regulations.

Safety data sheet available on request.

Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 11*). Only completely emptied cans can be recycled.

Verbrauchsrechner

HOW MUCH COATING DO I NEED?

With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.

To the finish calculator