Twice as much coverage through high oil content - saves time and money!
Decorative, satin-matt oil based protective finish for exterior wood furniture. Microporous, breathable finish allowing the wood to breath and reduces the risk of swelling and shrinkage. Water-repellent, extremely weather- and UV-resistant. Does not crack, flake, peel or blister. Easy to renew, no sanding or primer necessary. Easy to apply, does not dry during application. Osmo One Coat Only HSPlus has a minimal amount of solvent, works
without any biocides and preservatives, is high solid and thus has a very high coverage. With only one coat one achieves the optimal surface protection. When dry, the finish is safe for humans, animals and plants (suitable for children’s toys as per EN 71.3 (European norm) and is resistant to
perspiration and saliva in accordance with DIN 53160 (German industrial norm).
All exterior wood furniture. Ideal for the renovation of old microporous woodstains.








Ingredients
Based on natural vegetable oil, iron oxide and organic pigments, titanium dioxide (white pigment), siccatives (drying agents) and water-repellent additives. Dearomatised white spirit (benzenefree).
Storage
5 years and longer if stored in the originally closed can. If thickened by frost, store at room temperature for 24 hours prior to use.
COLOUR CODE | CAN SIZE LITRE | ARTICLE NUMBER | |
---|---|---|---|
| 0.75 | 11101542 | |
2.50 | 11101544 | ||
| 0.75 | 11101552 | |
2.50 | 11101554 | ||
| 0.75 | 11101562 | |
2.50 | 11101564 | ||
| 0.75 | 11101572 | |
2.50 | 11101574 | ||
| 0.75 | 11101060 | |
2.50 | 11101065 | ||
| 0.75 | 11101450 | |
2.50 | 11101455 | ||
| 0.75 | 11101480 | |
2.50 | 11101485 | ||
| 0.75 | 11101030 | |
2.50 | 11101035 | ||
| 0.75 | 11101210 | |
2.50 | 11101215 | ||
| 0.75 | 11101390 | |
2.50 | 11101395 | ||
| 0.75 | 11101360 | |
2.50 | 11101365 | ||
| 0.75 | 11101420 | |
2.50 | 11101425 | ||
| 0.75 | 11101120 | |
2.50 | 11101125 | ||
| 0.75 | 11101270 | |
2.50 | 11101275 |
NUMBER OF COATS
One coat is enough!


Wood surface must be clean, dry and frostfree (moisture content max. 20 %). Osmo One Coat Only HSPlus is ready-to-use, please do not thin, stir
well before use. Old microporous finishes must be cleaned thoroughly before application. Lacquers must be removed by sanding. Always wear a
dust mask when sanding. If additional protection against blue stain and rot is desired (especially for soft woods as pine), pre-treat, if possible all sides, with Osmo WR Base Coat. Use biocides safely. Always read the label and product information before use.
The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
Apply thinly and evenly along the wood grain with either an Osmo hand brush or the Osmo Microfibre Roller, and spread well. Allow for good ventilation whilst drying for approx. 12 hours.
With Osmo Brush Cleaner (free of aromatic compounds).
Approx. 12 hours (normal climatic conditions, 20-23°C/ 50-65 % rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times. After 2-3 weeks, the surface is fully cured.
The transparent colour tone of the finish will be influenced by the woods natural colour, causing the result to deviate from the colour shown on the colour chart. If applied too thickly, this product may leave shiny areas. However, these shiny areas will weather naturally within a short period of time
leaving an even, satin-matt appearance. After thorough drying, for further protection in an exterior environment please apply the Osmo UV-Protection-Oil clear (410 biocidefree or 420 with surface protection). This also protects against dirt and increases the durability of the finish.
Please only use the Natural Oil Woodstain white 900 when painting over the One Coat Only HSPlus white spruce. Rough or striated wood will need a larger quantity of material due to its surface structure. Some wood species „bleed“ natural water soluble ingredients during weathering.
Keep out of reach of children.
Safety data sheet available on request.
Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 12). Only completely emptied cans can be recycled.

HOW MUCH COATING DO I NEED?
With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.