Opaque wood finish in a multitude of colours – ideal for the exterior
Extremely weather-resistant and UV-stable, opaque satin wood finish for the exterior. Osmo Garden Colour is breathable and water repellent. The dried finish is safe for humans, animals and plants (resistant to saliva and perspiration acc. German DIN 53160, suitable for children's toys acc. EN 71.3).
Osmo Garden Colour is best suited for all exterior wood: timber cladding, balconies, window shutters, fencing, pergolas, garden sheds, garden furniture and carports.







Ingredients
Based on a polymer dispersion, titanium dioxide (white pigment), iron oxide and organic pigments, additives and preservatives (BIT and CIT/MIT). Solvent: water. This product fulfils EU regulations according to the VOC content of max. 130 g/l (Cat. A/d (2010). This product contains max. 130 g/l VOC. Detailed declaration of ingredients available upon request.
Storage
2 years or longer if stored in the originally closed container. Do not expose to frost or temperatures above 30 °C!
COLOUR CODE | CAN SIZE LITRE | ARTICLE NUMBER | |
---|---|---|---|
| 0.75 | 12400040 | |
| 0.75 | 13100305 | |
| 0.75 | 13100315 | |
| 0.75 | 13100322 | |
| 0.75 | 13100092 | |
| 2.50 | 13100091 | |
| 0.75 | 13100338 | |
| 2.50 | 13100340 | |
| 0.75 | 13100344 | |
| 2.50 | 13100346 | |
| 0.75 | 13100350 | |
| 2.50 | 13100352 | |
| 0.75 | 13100326 | |
| 2.50 | 13100328 | |
| 0.75 | 13100332 | |
| 2.50 | 13100334 | |
| 0.75 | 13100339 | |
| 2.50 | 13100341 | |
| 0.75 | 13100345 | |
| 2.50 | 13100347 | |
| 0.75 | 13100351 | |
| 2.50 | 13100353 | |
| 0.75 | 13100048 | |
| 2.50 | 13100047 | |
| 0.75 | 13100222 | |
| 2.50 | 13100223 |
NUMBER OF COATS
Two coats on an untreated substrate; for renovations, normally one coat on the clean surface is sufficient.




Wood surface must be clean, dry and frost-free (outside temperature 10°C, moisture content max. 20%). Osmo Garden Colour is ready to use. Do not thin. Stir well. If possible, please apply first coat to all sides before installation. Clean and sand old intact finishes – remove any damaged finishes (sand away). Always wear a dust mask while sanding. If additional protection against blue stain, rot and insects is desired, treat raw wood with Osmo WR Base Coat – if possible on all sides.
The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
With Osmo Flat Brush or Osmo Microfibre Roller, apply to clean dry wood thinly and quickly lap for lap with the grain or in a spray application. Leave to dry for 3-4 hours under good ventilation. After drying, fine sanding between coats as needed. Apply the second coat also thinly and evenly. If possible, apply the first coat to all sides prior to installation. For renovations, one coat is usually sufficient.
Immediately after use, with soap and water.
Approx. 3-4 hours (normal climatic conditions, 20-23°C/ 50-65% rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times.
Many wood species contain water-soluble coloured extractives which may leach out naturally when weathered. The oils and resins in exotic wood species and certain hardwoods (Oak, Locust, Larch, etc.) must weather away prior to application. This makes the wood absorbent and the wood finish bonds optimally.
Keep out of reach of children.
Contains
benzisothiazolinone (BIT);
mixture of: chloromethylisothiazolinone (CIT) and methylisothiazolinone (MIT) (3:1)
May produce an allergic reaction.
If medical advice is needed, have product container or label at hand.
Safety data sheet available on request.
Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 12). Only completely emptied cans can be recycled.

HOW MUCH COATING DO I NEED?
With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.