Wood Wax Finish Clear Extra Thin
colours
Wood coating for oily and resinous hardwoods!
Transparent, satin-matt Osmo finish, which combines all the advantages of oils and waxes in one unique product. Osmo Wood Wax Finish Clear Extra Thin is resistant to water and dirt, is very durable and smoothens wood surfaces. In comparison to conventional finishes, the natural vegetable oils and waxes allow for an even colouring and a harmonic, smooth surface result. Easy application – no need for a primer or sanding between coats – saves time and money. It meets the wood’s natural demands: It is microporous and does not crack, flake, peel or blister. The surface will be protected against common household substances such as wine, beer, cola, coffee, tea, fruit juice, milk and water according to DIN 68861-1C – no water spots. The dried finish is safe for people, animals and plants (saliva-resistant and sweatproof acc. DIN 53160, suitable for children’s toys acc. EN 71.3).
Osmo Wood Wax Finish Clear Extra Thin is for all interior wood furniture. It is particularly well suited for the treatment of dark hardwoods such as Meranti, Wenge, Merbau etc. Trial application is most definitely recommended.
Ingredients
Based on natural vegetable oils and waxes, paraffins. Siccatives (drying agents) and water-repellent additives. Dearomatised white spirit (benzene-free).
Storage
5 years and longer if stored in the originally closed can. If thickened by frost, store at room temperature for 24 hours prior to use.
| COLOUR CODE | CAN SIZE LITRE | ARTICLE NUMBER | |
|---|---|---|---|
| 0.75 | 10200001 | |
| 2.50 | 10200002 | ||
| 25.00 | 10200003 |
NUMBER OF COATS
Two coats on raw wood; for renovations, normally one coat on the clean surface is sufficient – without sanding!
Wood surface must be clean and dry (moisture content max. 18%). Wood Wax Finish Clear Extra Thin is ready-to-use. Do not thin, stir well before use. Clean or slightly sand old microporous finishes, remove old varnish (Osmo Paint Remover or by sanding). Always wear a dust mask when sanding. Small cracks, larger dents and small holes in the wood can be filled with Osmo Woodfiller. Sand carefully before application starting with a coarse paper – final sanding P 100 – 120. Remove dust etc. thoroughly from the surface with a brush or vacuum cleaner before application. If possible treat wood on all sides before installation.
The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
Osmo Wood Wax Finish Clear Extra Thin can be brushed, wiped, dipped or sprayed (in closed chambers). Apply evenly along the wood grain with a brush or cloth. 1st coat: Apply thinly. Leave to dry approx. 30 minutes. Remove all surplus. Recoat areas not sufficiently treated. 2nd coat: Apply thinly. Leave to dry approx. 30 minutes. Remove all surplus.
With Osmo Brush Cleaner (free of aromatic compounds).
Approx. 12 hours (normal climatic conditions, 20-23°C/ 50-65 % rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times. After 2-3 weeks, the surface is fully cured.
Natural oils accentuate the natural colour tone and grain of wood (permanent wet look). Caution: For cupboards, wardrobes and drawers, only 1 thin coat should be applied with a cloth.
Keep out of reach of children.
Safety data sheet available on request.
Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 12). Only completely emptied cans can be recycled.
HOW MUCH COATING DO I NEED?
With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.
