Osmo Farbe

Clear Oil Wood Finish

colours

Extraordinarily versatile – for special applications on exterior wood!

Clear, slightly glossy wood coating based on natural oil for exterior use. Microporous surface allows wood to breathe and reduces swelling and shrinkage. Water-repellent, will not crack, peel, flake or blister. Penetrates deeply and smoothens the wood surface with as little as one coat. No sanding necessary, just simply recoat; no primer is needed. Easy and seamless application. Finish stays workable while coating. The dry finish is safe for humans, animals and plants (resistant to saliva and perspiration acc. German DIN 53160, suitable for children‘s toys acc. EN 71.3).

Osmo Clear Oil Wood Finish is an extraordinarily versatile wood coating with many possibilities for use on wood surfaces in outdoor areas. It is ideal as a base coat for softwood, in particular rough sawn or greyed and weathered wood surfaces, to even out varying absorption rates. Osmo Clear Oil Wood Finish is also suitable as a slightly glossy top coat for Osmo One Coat Only HSPlus or Country Colour, when a slightly glossy and low maintenance surface is desired, expect for on white surfaces.

Based on renewable raw materialsMicroporous and breathable surfaceWater and dirt repellent surfaceRecoatable after approx. 10-12 hours16 m²/1 lVersatile in use
Oil advantages – Simple application, Water beading effect, No flaking or peelingSafe for humans, animals and plants (when dry) - Suitable for children's toys - According to DIN EN 71.3; fast to perspiration and saliva
Product information sheetpdf, 239 KBFull declarationpdf, 185 KBSafety datasheetpdf, 171 KB

Ingredients

Based on natural plant oils (sunflower oil, soybean oil), siccatives (drying agents) and water-repellent additives. Volatile component: dearomatised white spirit (benzene-free). EU limit value for this product (cat. A/e): 400 g/l VOC (2010). This product contains max. 400 g/l VOC. Detailed declaration of ingredients available upon request.

Storage

5 years or longer if stored in the originally closed container. If thickened by frost, store at room temperature for 24 hours prior to use.

COLOUR CODECAN SIZE LITREARTICLE NUMBER

000 Clear

Satin

0.7511600001
2.5011600002
25.0011600003

NUMBER OF COATS
One coat on the cleaned surface is enough.

TOOLS
Flat BrushMicrofiber Roller

Wood surface must be clean, dry and frost-free (moisture content max. 20%). Already greyed or weathered wood should be refreshed and cleaned with Osmo Wood Reviver Power-Gel, or at least remove any dirt and loose wood fibres. Osmo Clear Oil Wood Finish is ready to use. Do not thin. Stir well before use. If possible, please apply base coat to all sides before installation. Old microporous stains need to be cleaned. Old paints, varnishes and lacquers must be removed. Always wear a dusk mask while sanding. If additional protection against blue stain, rot and insects is desired, pre-treat the wood if possible on all sides with Osmo WR Base Coat.

The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.

As a base coat: with Osmo Flat Brush or Microfibre Roller, apply thinly along the wood grain and spread well. Ventilate well while drying for 10-12 hours. Afterwards, carry out application with Osmo Country Colour etc.
As a slightly glossy top coat: with Osmo Flat Brush or Microfibre Roller, apply one coat thinly along the wood grain to the thoroughly dried wood surface that has been pre-treated with a pigmented exterior Osmo finish and spread well.
Important: Base coat must be thoroughly dried! When renovating, one coat applied to the clean and dry surface is usually sufficient.

With Osmo Brush Cleaner (free of aromatic compounds).

Approx. 12 hours (normal climatic conditions, 20-23°C / 50-65 % rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times.

Osmo Clear Oil Wood Finish is clear and, therefore, does not protect against UV radiation from the sun (greying). Not suitable for single product applications on areas exposed to weathering (esp. timber decking). Due to its surface texture, ribbed or rough sawn timber absorbs significantly more product. For areas highly exposed to weather, such as gables, post caps, weatherboard, window sills, please calculate with significantly shorter renovation intervals. Horizontally mounted wood should have at least a 15-degree angle. Sharp edges must be rounded (radius > 2 mm). If the greying process has already begun, refresh the surface with Osmo Wood Reviver Power Gel and recoat. Due to high oil content, Osmo Clear Oil Wood Finish exhibits a light yellowing effect when used on white pretreated surfaces. Therefore, we recommend using Osmo Natural Oil Woodstain 900 White as a top coat in such cases. 

Keep out of reach of children.

Safety data sheet available on request.

Warning: Materials impregnated with liquid product, such as cloths, may self-ignite. After use, let the materials to dry completely either spread out flat or in a closed metal container and then dispose of them properly.

EU limit value for this product

(cat. A/e): 400 g/l VOC.

This product contains max.

400 g/l VOC.

Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 12). Only completely emptied cans can be recycled.

Verbrauchsrechner

HOW MUCH COATING DO I NEED?

With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.

To the finish calculator