Unique UV protection for indoor areas!
Clear or transparent coloured, satin wood coating with a wax-like character for interior use. Osmo Uviwax® UV-Protection guards the lignin in the wood against harmful UV radiation. The natural yellowing of wood is greatly reduced, and the natural, light-coloured wood tone is preserved for a long time. Osmo Uviwax® UV-Protection is stain-resistant, water-repellent and abrasion-resistant and smoothens the surface. Suitable for wood; microporous surface will not crack, peel, flake or blister. The dry finish is safe for humans, animals and plants (resistant to saliva and perspiration acc. German DIN 53160, suitable for children’s toys acc. EN 71.3).
Osmo Uviwax® UV-Protection is suitable for single product applications on wall and ceiling panelling as well as cabinets and doors in indoor areas. It is also suitable for recoating sawn edges and screw holes, additional mouldings, boards etc. that have been factory finished with Osmo Uviwax® UV-Protection. Suitable for all light-coloured wood species.








Ingredients
Polymer dispersion, waxes as well as UV protective additives, titanium dioxide (white pigment) and preservatives (BIT and CIT/MIT). Solvent: water. EU limit value for this product (cat. A/e): 130 g/l VOC (2010). This product contains max. 90 g/l VOC. Detailed declaration of ingredients available upon request.
Storage
2 years or longer if stored in the originally closed container. Do not expose to frost or temperatures above 30 °C!
COLOR CODE | CAN SIZE LITRE | ARTICLE NUMBER | |
---|---|---|---|
| 0.75 | 13200051 | |
2.50 | 13200050 | ||
10.00 | 13200145 | ||
| 0.75 | 13200135 | |
2.50 | 13200136 | ||
10.00 | 13200056 |
NUMBER OF COATS
Two coats on raw wood; for renovations, normally one coat on the clean surface is sufficient – without sanding!


Wood surface must be clean, dry and frost-free (moisture content max. 18%, coating temperature at least +10°C). Osmo Uviwax® UV-Protection is ready to use. Do not thin. Stir well before use. Clean old microporous stains thoroughly. Old paints, varnishes and lacquers must be completely removed. Always wear a dust mask while sanding. Degrease very resinous woods (e.g. Larch) with Osmo Brush Cleaner and Thinner. Osmo Uviwax® UV-Protection is to be used alone and solely applied to raw wood. If necessary, sand wood again with fine sandpaper. Wood treated with Osmo Uviwax® UV-Protection generally only need to be cleaned and recoated.
The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
With Osmo Flat Brush apply thinly, quickly and evenly along the wood grain and spread well. Allow to dry for approx. 3-4 hours under good ventilation.
If necessary, sand surface with fine sandpaper (grit P360) before applying the second coat. After drying, apply a second coat also thinly and quickly. For renovations, one coat is usually sufficient.
Immediately after use, with soap and water.
Approx. 3-5 hours (normal climatic conditions, 20-23°C/ 50-65% rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times.
Uviwax® UV-Protection is to be used alone. Please do not dilute or mix with other finishes. If a surface treated with Uviwax® UV-Protection should be recoated in a different colour, we solely recommend using Osmo Interior Wax.
If medical advice is needed, have product container or label at hand.
Keep out of reach of children.
Contains
Adipohydrazide
;
benzisothiazolinone (BIT), methylisothiazolinone (MIT).
(preservatives).
May produce an allergic reaction.
Safety data sheet available on request.
EU limit value for this product
(cat. A/e): 130 g/l VOC.
This product contains max.
90 g/l VOC.
Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 12). Only completely emptied cans can be recycled.

HOW MUCH COATING DO I NEED?
With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.