Hard-wearing finish with a wax-like character for wood for interior use!
Transparent or opaque, satin and hard-wearing wood finish with a wax-like character for indoor areas. Osmo Interior-Wax is stain-resistant, water-repellent and abrasion-resistant and smoothens the surface. The wood grain remains visible. Simple application – no primer or sanding between coats needed – this saves time and money. Suitable for wood; microporous surface will not crack, peel or flake. The dry finish is safe for humans, animals and plants (resistant to saliva and perspiration acc. German DIN 53160, suitable for children’s toys acc. EN 71.3).
Osmo Interior-Wax is suitable for the protection and decorative finishing of wood in indoor areas: wall and ceiling panelling, moulding and beams as well as furniture, doors and children’s toys. It is also suitable for recoating and repairing wood factory finished with Osmo Interior-Wax White Transparent (7393) or White Opaque (7394) and for recoating old wooden ceiling panelling.








Ingredients
On the basis of a polymer dispersion, waxes, titanium dioxide (white pigment) additives and preservatives (BIT & CIT/MIT). Solvent: water. This product fulfils EU-Regulation (2004/42/EC) according to the VOC limit value max. 130 g/l (Cat. A/d (2010). Full declaration of ingredients on request.
Storage
2 years or longer if stored in the originally closed container. Do not expose to frost or temperatures above 30 °C!
COLOUR CODE | CAN SIZE LITRE | ARTICLE NUMBER | |
---|---|---|---|
| 0.75 | 13100226 | |
2.50 | 13100227 | ||
10.00 | 13100234 | ||
| 0.75 | 13100230 | |
2.50 | 13100231 | ||
10.00 | 13100236 |
NUMBER OF COATS
Two coats on raw wood; for renovations, normally one coat on the clean surface is sufficient – without sanding!


Wood surface must be clean and dry (maximum moisture content 18 %). Clean or slightly sand old finishes. Trial application recommended. If there is insufficient gradient or insufficient adhesion, the old coat has to be removed. Always wear a dust mask while sanding. Small cracks, larger dents and small holes in the wood can be filled Osmo Wood Filler. Remove dust etc. thoroughly from the surface before application. Apply on frost-free wood only, and at temperatures of at least 10 °C. Osmo Interior-Wax is ready to use, please do no thin, stir well before use. The finished surface is influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
With either Osmo Flat Brush or Osmo Microfibre Roller apply thinly and evenly along the wood grain and spread well. Allow to dry for approx. 3 - 4 hours. If necessary, do a fine-grained (P 360) sanding between coats. After drying apply a second thin coat as before. Due to the quick drying properties, do not make sections too wide. For renovations 1 coat will be sufficient for most cases.
Immediately after use, with soap and water.
Approx. 3-5 hours (normal climatic conditions, 20-23°C/ 50-65% rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times.
One coat of Interior-Wax White Opaque creates a more intense colour than two coats of Interior-Wax White Transparent.
If medical advice is needed, have product container or label at hand.
Keep out of reach of children.
Contains
benzisothiazolinone (BIT), methylisothiazolinone (MIT).
(preservatives).
May produce an allergic reaction.
Safety data sheet available on request.
EU limit value for this product
(cat. A/d): 130 g/l VOC.
This product contains max.
90 g/l VOC.
Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 12). Only completely emptied cans can be recycled.

HOW MUCH COATING DO I NEED?
With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.