Highly pigmented waterborne pore filler for engineered wood products
Osmo Pore Filler Aqua is a highly pigmented, waterborne pore filler with high solids content, physical drying. It possesses enormous filling and hiding power, is fast drying and can be sanded well. Suitable for use under any opaque Osmo Spray-Wax.
Acts as a base and mid coat on wood and engineered wood products in indoor areas, for example MDF boards.








Ingredients
Based on a modern Aquatec binding agent, iron oxides, titanium dioxide (white pigment), additives and preservatives (BIT & CIT/MIT). Solvent: water. EU limit value for this product (cat. A/d): 130 g/l VOC (2010). This product contains max. 50 g/l VOC. Detailed declaration of ingredients available upon request.
Storage
2 years or longer if stored in the originally closed container. Do not expose to frost or temperatures above 30 °C!
COLOUR CODE | CAN SIZE LITRE | ARTICLE NUMBER | |
---|---|---|---|
| 2.50 | 11102030 | |
| 11102032 |
NUMBER OF COATS
One coat is sufficient; a top coat is absolutely essential.





No preparation for improved bonding necessary. Osmo Pore Filler Aqua is ready for use. Do not thin. Stir well. Wood surface must be clean, dry and frost-free (moisture content max. 12%). Old paints, varnishes and lacquers must be removed. Always wear a dust mask when sanding. Fill in smaller cracks, larger joints or holes in wood (Osmo Wood Filler). Thoroughly sand prime sheeting, e.g. on MDF boards. The surface preparation determines the quality of the final surface. Remove dust properly after sanding.
The finished surface and the product coverage are influenced by several factors, including the condition of the wood. Therefore, a trial application is always required, especially for unfamiliar surfaces.
Optimal application temperature for material, room and subsurface is 18° - 25° C! Flow cup spray gun: nozzle: 2.0-2.5mm, vaporiser air pressure: 1.6-2.2 bar; Airless: nozzle: 0.23-0.28 mm, material pressure: 80-120 bar; Airmix: nozzle: 0.23-0.28 mm, material pressure: 80-100 bar vaporiser air pressure: 1.2-1.8 bar. Drying on tray trolley or forced, depending on technical requirements. After drying intermediate sanding P 240-400. Repeat process if necessary. Afterwards carry out a top coat with Osmo Spray-Wax. This recommended application is the standard Osmo application recommendation. For smaller areas, alternative application methods are possible, e.g. with a roller or brush. Please consult our application technologists.
Immediately after use, with soap and water.
Approx. 4-5 hours (normal climatic conditions, 20-23°C/ 50-65% rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times.
Top coat required! Insufficient drying can lead to blocking or inadequate adhesion for subsequent surface coatings. Due to the multitude of different requirements, optimal drying procedures must be determined individually. Adhesion tests on the whole surface composition are always required. To perform these, carry out a trial application under practical conditions.
If medical advice is needed, have product container or label at hand.
Keep out of reach of children.
Contains
Adipohydrazide
;
benzisothiazolinone (BIT);
mixture of: chloromethylisothiazolinone (CIT) and methylisothiazolinone (MIT) (3:1)
(preservatives).
May produce an allergic reaction.
Safety data sheet available on request.
EU limit value for this product
(cat. A/d): 130 g/l VOC.
This product contains max.
50 g/l VOC.
Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 12). Only completely emptied cans can be recycled.

HOW MUCH COATING DO I NEED?
With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.