Osmo Farbe

Polymer Composite Maintenance Oil

colours

Ideal protection against dirt and stains!

Clear satin Polymer Composite Maintenance Oil penetrates the surface and will not build a film on the surface. Through the impregnation, the surface becomes water repellent as well as resistant to dirt and stains. 

Osmo Polymer Composite Maintenance Oil is suitable as a clear care product for maintaining and restoring weathered Wood Polymer Composites (WPC) and Bamboo Polymer Composites (BPC). Especially suitable for decking, privacy screens and garden furniture made of WPC or BPC. Not suitable for co-extruded surfaces.

Based on renewable raw materialsMicroporous and breathable surfaceWater and dirt repellent surfaceEasy to clean and maintainRecoatable after approx. 8-10 hours40 m²/1 l
Oil advantages – Simple application, Water beading effect, No flaking or peelingSafe for humans, animals and plants (when dry) - Suitable for children's toys - According to DIN EN 71.3; fast to perspiration and saliva
Product information sheetpdf, 106 KBFull declarationpdf, 185 KBSafety datasheetpdf, 172 KB

Ingredients

Based on natural plant oils (sunflower oil, soybean oil, thistle oil) , paraffin, siccatives (drying agents) and water repellent additives. Dearomatized white spirit (benzene-free). VOC classification in compliance with EU regulations (2004/42/EC): out of scope. Detailed declaration of ingredients available upon request.

Storage

5 years or longer if stored in the originally closed container.

COLOR CODECAN SIZE LITREARTICLE NUMBER

030 Clear

Satin

1.0011500111

NUMBER OF COATS
One coat on the cleaned surface is enough.

TOOLS
Flat BrushFlooring/Decking brushPadCloth

The surface must be weathered, cleaned, dry and frost-free. Osmo Polymer Composite Maintenance Oil is ready to use. Do not thin. Stir well. Prior to application, the surface must be thoroughly cleaned with Osmo Polymer Composite Cleaner 8021. This ensures sufficient bonding. Before applying Osmo Polymer Composite Maintenance Oil, rinse thoroughly with water and allow to dry. 

Impregnation results depend significantly on the substrate and its condition. Therefore a trial application must always be carried out. With the multitude of various polymer composite (WPC & BPC) products on the market, a general recommendation for the impregnation of all products is not possible. Some polymer composites, especially those without absorbent wood or bamboo content in the surface, cannot be impregnated and are not suitable for treatment! Product coverage depends significantly on the absorption rate of the substrate. Smooth, fresh WPC or BPC absorbs much less oil than the stated application amount, while strongly weathered, rough substrates absorb much more.

With Osmo Flat Brush or Osmo Decking Brush, apply very thinly and spread well. Remove excess material (pooling or streaks) with a clean dry Osmo Decking Brush. Important: the liquid oil must be absorbed into the surface. There must not be any oil remaining on the surface or in grooves. Excess oil dries very slowly and produces a glossy oil layer without sufficient adhesion to the substrate. Leave to dry for 8-10 hours. Ventilate well while drying. 

With Osmo Brush Cleaner (free of aromatic compounds).

Approx. 8-10 hours (normal climatic conditions, 23 °C/ 50% rel. humidity). Ventilate well while drying. Lower temperatures and/or higher air humidity may increase drying times. After 2-3 weeks, the surface is fully cured.

Oils enhance the natural colour of the substrate (permanent wet effect). Trial application is required! Impregnation may influence the slip resistance of the original surface. White or very light-coloured surfaces may become slightly yellow from oiling! Non-absorbent surfaces, such as glass, glazed tiles, ceramic or plastic, must be not treated (impregnated). 

Keep out of reach of children.

Safety data sheet available on request.

Warning: Materials impregnated with liquid product, such as cloths, may self-ignite. After use, let the materials to dry completely either spread out flat or in a closed metal container and then dispose of them properly.

EU limit value for this product

: out of scope.

Dispose of product residuals according to the official guidelines (European Waste Code (EWC)-Code 08 01 12). Only completely emptied cans can be recycled.

Verbrauchsrechner

HOW MUCH COATING DO I NEED?

With our finish calculator, the right amount of coating necessary for your project can be calculated quickly and easily.
Please follow our advice in the product information sheets for the correct application.

To the finish calculator